Six problems to avoid when installing cabinets - KCTV5

Six problems to avoid when installing cabinets


Provided by

Installing kitchen cabinets can come with some challenges. Over the years of my work as a Denver-area carpenter, I have learned how to avoid common cabinet installation problems. Here are the top six problems, and how to prevent them.

1. Changing the dimensions of the cabinets: If you are remodeling a space and are replacing cabinets, the simple task of swapping out the same sizes in the same layout is pretty easy.  A 30 wide base cabinet paired with a 36 sink baseas an exact replacement for an existing 30 base and 36 sink is nearly a complete guarantee for success. One problem that remodelers face is looking for something different, bigger or better.  With these tasks, change is the norm, and that is where it starts to get complicated.

2. Too much (or lack of) precision in the plan: When a new layout is thought up, the plan may involve moving walls, relocating plumbing, electrical service, etc. Cabinets come in stock sizes and most folks go this route as opposed to 100% custom from a specialty builder. Combining pairs or sets of cabinets to fill the wall-to-wall space can usually be done with the stock sizes. Swapping a 15 drawer unit for an 18 drawer unit may allow you to get your overall widths down to the very inch.

If your plan uses 100% of the wall-to-wall width a slight error in measuring may have you trying to jam 96 inches of cabinet into a space 95 inches wide.  A better plan would allow for the use of a blind corner and/or the use of some filler trim.  Filler trim can be added last and scribed for an exact fit. Whether your plan is produced in AutoCAD with 1/16 precision, or sketched on the back of a cocktail napkin, planning a little wiggle room will save the day.

3. Installing cabinets on sloped surfaces: In older homes, most floors are never perfectly level.  (Even some new homes fall in this group.) Installing cabinets on sloped surfaces is not recommended, since they look really bad and the doors may not swing properly. The normal installation method is to find the highest point in the layout and start thereit is much easier to shim up a cabinet, rather than lower a high spot in the floor. When the tops of all of the cabinets are in the same plane the counter tops will sit flat level and true. In the case of some natural stone counter tops, this will prevent cracks or breaks from forming over high points. In most homes these height differences are minor and can easily be shimmed. A number of years ago I worked in a kitchen where 6 of slope was encountered over an 8 foot run. Needless to say it was challenging.

4. Gaps between the counter top and the wall: While not so much of an issue with the actual installation of the cabinets, the lack of square poses more problems with counter tops, especially with molded laminates that have integral backsplashes. A run out along an obtuse corner may leave large gaps between a molded backsplash and the wall. Here working with tile or slabs that are custom scribed to fit the space will make these visual errors disappear. The cabinet trim may be beveled to look square even though the space is not. Bigger errors in room shape require more finesse in fitting the parts together. When properly done the eye never picks up on this out-of-square problem

5. Walls that are not flat: Similar to a floor not being level, wall unevenness can be corrected with shims. Here the goal is to have all of the cabinet faces lying in the same plane. This provides the clean look, that showcases a great install. The use of various height and depth cabinets can help mask these type of errors.

6. Hanging a cabinet on drywall: Hanging a wall cabinet with a pair of drywall screws set only in the drywall will work for a few minutes or until the first set of dishes are installed. Then the whole shebang will come crashing down. If a strip to studs remodel is taking place, the simple task of adding blocking between the studs will allow for solid screw placement every time. If this is not in your plan, heavy duty toggle bolts combined with some screws hitting studs will keep your cabinets on the wall.  Another way to help in this department is having all the cabinets attached to each other. Here the adjacent bigger neighbors can share the load of a skinny cabinet that does not hit a stud.

Kevin Stevens wrote this article for

  View original post.

Powered by WorldNow
KCTV 5 News

Online Public File:

Powered by WorldNow CNN
All content © 2014, KCTV; Kansas City, MO. (A Meredith Corporation Station) and WorldNow. All Rights Reserved.
For more information on this site, please read our Privacy Policy and Terms of Service.